書目名稱Englisch für Maschinenbauer網(wǎng)絡(luò)公開度學科排名
書目名稱Englisch für Maschinenbauer被引頻次
書目名稱Englisch für Maschinenbauer被引頻次學科排名
書目名稱Englisch für Maschinenbauer年度引用
書目名稱Englisch für Maschinenbauer年度引用學科排名
書目名稱Englisch für Maschinenbauer讀者反饋
書目名稱Englisch für Maschinenbauer讀者反饋學科排名
作者: NEX 時間: 2025-3-21 23:47
https://doi.org/10.1007/978-1-349-09851-4lunging it into cold water or oil. The edge of the chisel will now be very hard, but also very brittle. It is necessary to remove some of this brittleness, or else the chisel will break when in normal use. The process of removing some of this brittleness is called ..作者: 惡臭 時間: 2025-3-22 04:22 作者: AVANT 時間: 2025-3-22 08:17
The International Court of Justice accuracy of the work done on a lathe, depends on the skill and experience of the operator. A lot of time is taken for tool setting, tool changing,etc., with the result that it is unsuitable for production work. It is mainly used in tool rooms and workshops for the making of prototypes, and also for maintenance work.作者: TOM 時間: 2025-3-22 08:56 作者: Gyrate 時間: 2025-3-22 15:16
Hand Tools, the maintenance of equipment. It is therefore important that engineers should acquire sufficient knowledge and experience in the use of hand tools. Some of the most common hand tools are shown in Fig 1.2 and a brief description of their use is given below.作者: Gyrate 時間: 2025-3-22 17:50
The hardening of carbon steel tools,lunging it into cold water or oil. The edge of the chisel will now be very hard, but also very brittle. It is necessary to remove some of this brittleness, or else the chisel will break when in normal use. The process of removing some of this brittleness is called ..作者: Original 時間: 2025-3-23 00:20
Screw threads and tapers,l hole, as for example in a nut. There are many shapes and types of screw threads, each designed for a specific type of work. Each screw thread is made to a ., and some of the terms used in defining such a specification are given below.作者: Coronation 時間: 2025-3-23 03:04 作者: Bmd955 時間: 2025-3-23 07:47
Shapers and planers, the ., and no metal is removed during the .. To reduce the total machining time, it is necessary to reduce the time taken by the return stroke. This is ensured by a .. Fig 18.1 shows a typical shaper.作者: Legion 時間: 2025-3-23 13:42 作者: 粗糙濫制 時間: 2025-3-23 17:25 作者: sorbitol 時間: 2025-3-23 19:52
Sheet metal work,tal and is unsuited for mass production. In machine work, automatic machines are used to cut and form sheet metal. The production of household appliances, and parts for motor car bodies are typical examples of this kind of sheet metal work.作者: 膽小懦夫 時間: 2025-3-23 23:24 作者: Generalize 時間: 2025-3-24 04:29
Hand Tools,ols has been almost eliminated. However, hand tools are still required for many purposes in industry, like the making of prototypes and models, and in the maintenance of equipment. It is therefore important that engineers should acquire sufficient knowledge and experience in the use of hand tools. S作者: 消極詞匯 時間: 2025-3-24 10:17
Sheet metal work,re still in use for many types of work. In handwork, components in a wide variety of shapes and sizes can be produced from sheet metal with the help of hand and bench tools and a few simple machines. This kind of work requires a high degree of skill in the use of suitable tools to shape the sheet me作者: 負擔 時間: 2025-3-24 11:20 作者: 無瑕疵 時間: 2025-3-24 18:12 作者: Urgency 時間: 2025-3-24 19:53 作者: 農(nóng)學 時間: 2025-3-25 00:27 作者: Harpoon 時間: 2025-3-25 07:24 作者: 高談闊論 時間: 2025-3-25 10:41
Single point cutting tools,e removed from the body of a metal is similar to the action of a chisel as shown in Fig 1.1. The pointed part of the tool is a wedge which presses heavily on the body of the metal and tears off a chip when the metal moves relative to the tool.作者: offense 時間: 2025-3-25 13:01
Engineering inspection,turing industry today, it is easy to see that it is not possible to inspect all of them for . With modern production methods, it is possible to maintain a high degree of accuracy, but there are always small variations in dimensions, which must be kept within strict limits, to ensure the interchangea作者: 能夠支付 時間: 2025-3-25 17:13
The lathe,nternal, and also for the turning of . .. An additional feature of the lathe, is its ability to cut . on a surface that has already been machined. The accuracy of the work done on a lathe, depends on the skill and experience of the operator. A lot of time is taken for tool setting, tool changing,etc作者: intrude 時間: 2025-3-25 21:53 作者: CROW 時間: 2025-3-26 00:23 作者: AGONY 時間: 2025-3-26 07:13
The Intermediality of Narrative Literaturere still in use for many types of work. In handwork, components in a wide variety of shapes and sizes can be produced from sheet metal with the help of hand and bench tools and a few simple machines. This kind of work requires a high degree of skill in the use of suitable tools to shape the sheet me作者: 完全 時間: 2025-3-26 10:27
https://doi.org/10.1007/978-1-349-13958-3mperature than the metals being soldered. Two types of solder are commonly used. One is a ., which is an alloy of tin and lead. The other is a ., which is an alloy of copper and zinc and is often called ..作者: 脫落 時間: 2025-3-26 12:45
https://doi.org/10.1007/978-1-349-03196-2eak easily. Some metal components like crankshafts, connecting rods, spanners, etc, have to stand up to conditions of severe stress when in use. Components produced by the ., are much stronger than those produced by casting or by machining from solid bar material. The reason for this lies in the fac作者: 移植 時間: 2025-3-26 17:25 作者: FORGO 時間: 2025-3-26 23:31 作者: ARY 時間: 2025-3-27 03:56 作者: Blood-Clot 時間: 2025-3-27 08:00 作者: 雜色 時間: 2025-3-27 10:01
https://doi.org/10.1007/978-3-531-92254-6turing industry today, it is easy to see that it is not possible to inspect all of them for . With modern production methods, it is possible to maintain a high degree of accuracy, but there are always small variations in dimensions, which must be kept within strict limits, to ensure the interchangea作者: Grating 時間: 2025-3-27 15:09 作者: Dislocation 時間: 2025-3-27 17:55
https://doi.org/10.1007/978-94-017-4865-0on a table, and metal is removed from its surface by a single point metal cutting tool, which has a reciprocating motion. Metal is removed only during the ., and no metal is removed during the .. To reduce the total machining time, it is necessary to reduce the time taken by the return stroke. This 作者: GLIB 時間: 2025-3-28 00:11
Springer Fachmedien Wiesbaden 1997作者: abracadabra 時間: 2025-3-28 06:08
Overview: 978-3-322-91976-2作者: 旅行路線 時間: 2025-3-28 08:56 作者: BLINK 時間: 2025-3-28 13:46 作者: 煩人 時間: 2025-3-28 18:12 作者: progestogen 時間: 2025-3-28 21:08
https://doi.org/10.1007/978-981-13-2601-1e removed from the body of a metal is similar to the action of a chisel as shown in Fig 1.1. The pointed part of the tool is a wedge which presses heavily on the body of the metal and tears off a chip when the metal moves relative to the tool.作者: peptic-ulcer 時間: 2025-3-29 01:44
https://doi.org/10.1007/978-3-531-92254-6turing industry today, it is easy to see that it is not possible to inspect all of them for . With modern production methods, it is possible to maintain a high degree of accuracy, but there are always small variations in dimensions, which must be kept within strict limits, to ensure the interchangeability of components.作者: Triglyceride 時間: 2025-3-29 05:00
The joining of metals by soldering and welding,mperature than the metals being soldered. Two types of solder are commonly used. One is a ., which is an alloy of tin and lead. The other is a ., which is an alloy of copper and zinc and is often called ..作者: Hiatus 時間: 2025-3-29 07:56
Drills and drilling machines,e drilling of a hole of the . at the . can be difficult. A large number of tools and machines have been designed for the drilling of holes economically, accurately, and quickly, in all types of materials. A drilling machine can be used for many operations, some of which are the following:作者: 不能約 時間: 2025-3-29 11:31 作者: 感激小女 時間: 2025-3-29 16:58
Engineering inspection,turing industry today, it is easy to see that it is not possible to inspect all of them for . With modern production methods, it is possible to maintain a high degree of accuracy, but there are always small variations in dimensions, which must be kept within strict limits, to ensure the interchangeability of components.作者: 完成 時間: 2025-3-29 21:02 作者: Facet-Joints 時間: 2025-3-30 02:33 作者: 剝皮 時間: 2025-3-30 07:14
https://doi.org/10.1007/978-3-319-60201-1There are many ways in which metal components and sheets can be joined together. One way is by the use of mechanical fasteners like rivets, bolts and nuts, and set screws.作者: harpsichord 時間: 2025-3-30 08:17
https://doi.org/10.1007/978-3-319-02225-3Many types of materials are used in manufacturing industry today. Some of the more important ones are metals, alloys, and plastics. Different kinds of metals and alloys are used for different purposes and the diagram in Fig 6.1 shows some metals and alloys that are in common use.作者: 自戀 時間: 2025-3-30 13:42
https://doi.org/10.1007/978-3-030-26883-1The production of metal objects by the process of casting has been practiced for thousands of years. This is probably the quickest and most economical way of producing a metal component, particularly a large and complex one.作者: 揉雜 時間: 2025-3-30 19:14
The International Adjustment MechanismThe purpose of the heat treatment process is to improve the properties of a metal to the extent that:作者: BLANC 時間: 2025-3-30 22:21
https://doi.org/10.1007/978-3-319-96965-7A working machine is composed of many components, some of which are moving. There are many kinds of motion, of which ., and . are amongst the most important. In rotatory or rotary motion, the object is rotating around an axis or a point, in a clockwise or an anticlockwise sense.作者: invade 時間: 2025-3-31 00:59
The International Banking SystemA . is a toothed wheel which when meshed with other gears transmits motion from one part of a mechanism to another. The design of the gears determines the . between the shafts and the . ..作者: moratorium 時間: 2025-3-31 06:24 作者: VEIL 時間: 2025-3-31 12:37 作者: vertebrate 時間: 2025-3-31 13:52
The joining of metals by mechanical methods,There are many ways in which metal components and sheets can be joined together. One way is by the use of mechanical fasteners like rivets, bolts and nuts, and set screws.
