標題: Titlebook: Development of Infrared Techniques for Practical Defect Identification in Bonded Joints; Rachael C. Waugh Book 2016 Springer International [打印本頁] 作者: Levelheaded 時間: 2025-3-21 19:38
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints影響因子(影響力)
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints影響因子(影響力)學科排名
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints網絡公開度
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints網絡公開度學科排名
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints被引頻次
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints被引頻次學科排名
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints年度引用
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints年度引用學科排名
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints讀者反饋
書目名稱Development of Infrared Techniques for Practical Defect Identification in Bonded Joints讀者反饋學科排名
作者: 空氣 時間: 2025-3-21 22:17
https://doi.org/10.1007/978-3-658-34420-7er. By fulfilling these objectives pulse phase thermography has been shown to have strong potential as a technology that could be implemented as a practical and portable device for non-destructive evaluation of adhesive bonds in a variety of applications.作者: 甜瓜 時間: 2025-3-22 02:47
Logistik, Transport und LieferbedingungenPPT are identical so the modelling approach is able to recreate the experimental conditions and parameters used for both. The results obtained from the model are then compared to the PT results in each case. PPT phase result may then be created by processing the modelled PT results.作者: 率直 時間: 2025-3-22 07:30 作者: 維持 時間: 2025-3-22 12:34 作者: 皮薩 時間: 2025-3-22 13:19 作者: 皮薩 時間: 2025-3-22 19:54
Der internationale Marketing-Mixion and processing methods used in the current work are introduced and the importance of various variables studied. From this investigation knowledge of the importance of the experimental parameters is obtained and used in the remainder of experimental work.作者: 平項山 時間: 2025-3-22 23:00
Abgasnachbehandlung in Dieselmotoren,e thermography (PPT) defect detection was undertaken. While the addition of load using a test machine was found to enable defect detection using PPT it was not practical for onsite use. However the findings of this chapter enabled the development of a portable device, described in Chap.?8.作者: Fibroid 時間: 2025-3-23 04:41
The Physics and Implementation of Thermography,ion and processing methods used in the current work are introduced and the importance of various variables studied. From this investigation knowledge of the importance of the experimental parameters is obtained and used in the remainder of experimental work.作者: PANG 時間: 2025-3-23 08:33
Kissing Defects,e thermography (PPT) defect detection was undertaken. While the addition of load using a test machine was found to enable defect detection using PPT it was not practical for onsite use. However the findings of this chapter enabled the development of a portable device, described in Chap.?8.作者: 糾纏,纏繞 時間: 2025-3-23 09:55
Conclusions and Future Work,er. By fulfilling these objectives pulse phase thermography has been shown to have strong potential as a technology that could be implemented as a practical and portable device for non-destructive evaluation of adhesive bonds in a variety of applications.作者: AUGER 時間: 2025-3-23 14:47
Logistik, Transport und Lieferbedingungenication. The first step in this process is to categorise types of defects in adhesive bonds and then to develop reliable methods of non-destructive evaluation that can identify the defect type before tailoring the threshold criteria.作者: 驚惶 時間: 2025-3-23 22:02 作者: 形容詞詞尾 時間: 2025-3-24 01:04
Zusammenwirken von Regler und Strecken,to Triplex bonds as well as introducing three other case studies that have been carried out. These involve the application of PPT to different materials and in different environments to give information about bonded joints.作者: 完成 時間: 2025-3-24 03:21 作者: 易碎 時間: 2025-3-24 10:31
Non-destructive Evaluation,, which uses operational loading to obtain information about the system, is classed as passive. Active NDE techniques are considered as those that require the application of a load or stimulation other than that experienced in operation, to enable inspection of the component.作者: 悲痛 時間: 2025-3-24 11:30 作者: 衍生 時間: 2025-3-24 18:29 作者: PARA 時間: 2025-3-24 19:45 作者: 小溪 時間: 2025-3-25 01:44 作者: Isometric 時間: 2025-3-25 03:54 作者: figurine 時間: 2025-3-25 10:42
The Physics and Implementation of Thermography,itially provide an in depth review of the main types of thermography that use the addition of energy from light sources, namely pulsed, lock-in and pulse phase thermography. The types of detectors that may be used for these techniques are then considered. The underpinning physics of heat transfer th作者: 向外 時間: 2025-3-25 11:42 作者: Corral 時間: 2025-3-25 16:55
Numerical Modelling,has been created using Ansys. The model is aimed at determining the heat transfer process through a realistic defect, understanding the effect of the system and material parameters as well as being a predictive tool. The aim of the predictive tool is to determine the thresholds of defect detection, 作者: reflection 時間: 2025-3-25 20:45
Kissing Defects,uld be possible to identify a very thin air gap, therefore, a means of opening such defects was then considered. Kissing defects were?experimentally?simulated via the addition of silicon grease to the bond line. Initially work focussed on the use of the bending moment created through loading single 作者: Ingredient 時間: 2025-3-26 02:26 作者: 搜集 時間: 2025-3-26 04:52 作者: prodrome 時間: 2025-3-26 08:47 作者: 培養 時間: 2025-3-26 16:28
Grundlagen Export und Internationalisierungt and bulk materials. Where insufficient thermal property contrast exists defects have a limited effect on heat propagation through a component and therefore are not detected using PT or PPT.?A means of producing realistic kissing defects in bonded joints is established. The addition of a small load作者: parsimony 時間: 2025-3-26 17:28 作者: 性行為放縱者 時間: 2025-3-26 21:56
Introduction,t and bulk materials. Where insufficient thermal property contrast exists defects have a limited effect on heat propagation through a component and therefore are not detected using PT or PPT.?A means of producing realistic kissing defects in bonded joints is established. The addition of a small load作者: chassis 時間: 2025-3-27 04:06
Preliminary Results,n testing bonded joint configurations. In all samples experimentally simulated defects were spaced sufficiently so that they could be studied individually, without interference from surrounding defects.作者: QUAIL 時間: 2025-3-27 07:05
Book 2016mponent and therefore are not detected using PT or PPT, this thesis discusses the addition of a small load to bonds containing kissing defects which was found to open the defects sufficiently to enable their detection. .A low cost infrared detector, Flir Tau320, is compared to the research based pho作者: Debrief 時間: 2025-3-27 11:30 作者: 彩色的蠟筆 時間: 2025-3-27 14:00
2190-5053 of a small load to bonds containing kissing defects which was found to open the defects sufficiently to enable their detection. .A low cost infrared detector, Flir Tau320, is compared to the research based pho978-3-319-37377-5978-3-319-22982-9Series ISSN 2190-5053 Series E-ISSN 2190-5061 作者: evince 時間: 2025-3-27 20:23
Development of Infrared Techniques for Practical Defect Identification in Bonded Joints978-3-319-22982-9Series ISSN 2190-5053 Series E-ISSN 2190-5061 作者: 設想 時間: 2025-3-27 23:52 作者: 蘆筍 時間: 2025-3-28 04:06
Springer Theseshttp://image.papertrans.cn/d/image/269971.jpg作者: 轉換 時間: 2025-3-28 07:48
Grundlagen Export und Internationalisierungork on this matter has focused on the development of advanced ultrasonic techniques. The current thesis focuses on the use of thermography, specifically pulsed and pulse phase thermography (PT and PPT), for the identification of kissing defects.?Initially the thesis focuses on the application of PT 作者: 歡樂中國 時間: 2025-3-28 10:50
Logistik, Transport und Lieferbedingungenas the potential to affect the strength of that bond. Industry requires a method of not only identifying such defects but also the setting of threshold criteria, to define acceptable/unacceptable defects. The threshold criteria are dependent on where the joint is to be deployed and tailored its appl作者: 頌揚國家 時間: 2025-3-28 18:02
Die Internationalisierungsentscheidung Such techniques may be broadly classed as either passive or active. In the current work, techniques are considered passive if no additional stimulus or excitation is added to the structure or component for the purpose of the NDE technique. Hence, a NDE approach applied while a system is operational作者: 軍火 時間: 2025-3-28 22:27
Der internationale Marketing-Mixitially provide an in depth review of the main types of thermography that use the addition of energy from light sources, namely pulsed, lock-in and pulse phase thermography. The types of detectors that may be used for these techniques are then considered. The underpinning physics of heat transfer th作者: 極端的正確性 時間: 2025-3-29 02:28 作者: Headstrong 時間: 2025-3-29 07:05
Logistik, Transport und Lieferbedingungenhas been created using Ansys. The model is aimed at determining the heat transfer process through a realistic defect, understanding the effect of the system and material parameters as well as being a predictive tool. The aim of the predictive tool is to determine the thresholds of defect detection, 作者: deforestation 時間: 2025-3-29 10:46 作者: 準則 時間: 2025-3-29 12:22
Grundlagen der Dieseleinspritzung,ory based; using a test machine to impart load, and a high specification infrared detector to measure the thermal response. The current chapter focusses on the adaption of the technique to allow it to become more practical and accessible to industry. Firstly the use of a vacuum load to open experime作者: Motilin 時間: 2025-3-29 16:50 作者: 乞討 時間: 2025-3-29 20:11
https://doi.org/10.1007/978-3-658-34420-7p a reliable method of identifying kissing defects in adhesive bonds. The objectives and how they have been achieved are detailed in the current chapter. By fulfilling these objectives pulse phase thermography has been shown to have strong potential as a technology that could be implemented as a pra
